Chevrolet silverado 2012 Owner'S Manual Download Page 200 | Manualshive

Page: 200 / 608

background image

Black plate (52,1)

Chevrolet Silverado Owner Manual - 2012

5-52

Instruments and Controls

As soon as it is safe to do so,
carefully pull the vehicle over to the
side of the road and turn the ignition
off. Check the wiring connection to
the trailer and turn the ignition back
on. This message clears if the trailer
is reconnected. This message also
clears if you acknowledge it. If this
message still displays, either the
vehicle or the trailer needs service.
See your dealer.

See

“

Integrated Trailer Brake

Control System

”

under

Towing

Equipment on page 9

‑

106

for more

information.

ICE POSSIBLE DRIVE
WITH CARE

This message displays when ice
conditions are possible.

TRAILER CONNECTED

On vehicles with the Integrated
Trailer Brake Control (ITBC) system,
this message displays briefly when
a trailer with electric brakes is first
connected to the vehicle.

This message clears itself after
several seconds. This message also
clears if you acknowledge it. After
this message clears, the TRAILER
GAIN/OUTPUT display appears in
the DIC.

See

“

TRAILER GAIN/OUTPUT

”

under

Driver Information Center

(DIC) on page 5

‑

33

and

“

Integrated

Trailer Brake Control System

”

under

Towing Equipment on page 9

‑

106

for more information.

Washer Fluid Messages

WASHER FLUID LOW ADD
FLUID

This message displays when the
windshield washer fluid is low. Fill
the windshield washer fluid reservoir
as soon as possible. See

Engine

Compartment Overview on
page 10

‑

6

for the location of the

windshield washer fluid reservoir.
Also, see

Washer Fluid on

page 10

‑

29

for more information.

Vehicle
Personalization

Vehicle Personalization
(With DIC Buttons)

The vehicle may have customization
capabilities that allow you to
program certain features to one
preferred setting. Customization
features can only be programmed to
one setting on the vehicle and
cannot be programmed to a
preferred setting for two different
drivers.

All of the customization options may
not be available on the vehicle. Only
the options available will be
displayed on the DIC.

The default settings for the
customization features were set
when the vehicle left the factory, but
may have been changed from their
default state since then.

The customization preferences are
automatically recalled.

«
...
198
199
200
201
202
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Brand: Aries Pages: 3

Gasoline/Electric DS Golf Car 1996

Brand: Club Car Pages: 48

Brand: Sirius Satellite Radio Pages: 8

Brand: Nav TV Pages: 4

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Magneti Marelli Pages: 2

Brand: E&G Classics Pages: 4

Brand: Subaru Pages: 32

Brand: FALCON RIDGE Pages: 4

Brand: Axxess Pages: 16

Brand: Mercedes-Benz Pages: 27

Brand: Buick Pages: 112

QuadraTop Adventure Top S

Brand: Quadratec Pages: 13

Brand: AUTOTECH Pages: 2

Brand: Ocular Pages: 7

Brand: Hyundai Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands