Chevrolet silverado 2012 Owner'S Manual Download Page 195 | Manualshive

Page: 195 / 608

background image

Black plate (47,1)

Chevrolet Silverado Owner Manual - 2012

Instruments and Controls

5-47

Engine Power Messages

ENGINE POWER IS REDUCED

This message displays and a chime
may sound when the cooling system
temperature gets too hot and the
engine further enters the engine
coolant protection mode. See

Engine Overheating on page 10

‑

24

for more information.

This message also displays when
the vehicle's engine power is
reduced. Reduced engine power
can affect the vehicle's ability to
accelerate. If this message is on,
but there is no reduction in
performance, proceed to your
destination. The performance may
be reduced the next time the vehicle
is driven. The vehicle may be driven
at a reduced speed while this
message is on, but acceleration and
speed may be reduced. Anytime
this message stays on, the vehicle
should be taken to your dealer for
service as soon as possible.

Fuel System Messages

FUEL LEVEL LOW

This message displays and a chime
may sound if the fuel level is low.
Refuel as soon as possible. See

Fuel Gauge on page 5

‑

15

and

Fuel

on page 9

‑

79

for more information.

TIGHTEN GAS CAP

This message may display along
with the check engine light on the
instrument panel cluster if the
vehicle's fuel cap is not tightened
properly. See

Malfunction Indicator

Lamp on page 5

‑

25

. Reinstall the

fuel cap fully. See

Filling the Tank

on page 9

‑

84

. The diagnostic

system can determine if the fuel cap
has been left off or improperly
installed. A loose or missing fuel
cap allows fuel to evaporate into the
atmosphere. A few driving trips with
the cap properly installed should
turn this light and message off.

Key and Lock Messages

REPLACE BATTERY IN
REMOTE KEY

This message displays if a Remote
Keyless Entry (RKE) transmitter
battery is low. The battery needs to
be replaced in the transmitter.
See

“

Battery Replacement

”

under

Remote Keyless Entry (RKE)
System Operation on page 2

‑

3

.

Lamp Messages

TURN SIGNAL ON

This message displays and a chime
sounds if a turn signal is left on for
1.2 km (0.75 mi). Move the turn
signal/multifunction lever to the off
position.

«
...
193
194
195
196
197
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: iDataLink Pages: 106

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Cequent Pages: 9

Brand: kincrome Pages: 6

Brand: AA Products Pages: 4

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Ford 4” UNI-CAM

Brand: Nav TV Pages: 6

2007 9-3 Remote Starter

Brand: Saab Pages: 304

Brand: Mercedes-Benz Pages: 39

Brand: Mercedes-Benz Pages: 296

Brand: Hyundai Pages: 168

Brand: Belkin Pages: 30

Brand: Mitsubishi Pages: 141

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brand: Skoda Pages: 276

Brand: TRAMEC Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands