Chevrolet silverado 2012 Owner'S Manual Download Page 187 | Manualshive

Page: 187 / 608

background image

Black plate (39,1)

Chevrolet Silverado Owner Manual - 2012

Instruments and Controls

5-39

OUTPUT shows the power output to
the trailer any time a trailer with
electric brakes is connected. Output
is displayed in 0 to 10 bars. Dashes
may appear in the OUTPUT display.

To adjust trailer gain see

“

Integrated

Trailer Brake Control System

”

under

Towing Equipment on page 9

‑

106

for more information.

Battery

This display shows the current
battery voltage. If the voltage is in
the normal range, the value will
display. For example, the display
may read BATTERY 13 VOLTS.
Your vehicle's charging system
regulates voltage based on the state
of the battery. The battery voltage
may fluctuate when viewing this
information on the DIC. This is
normal.

Oil Pressure

This display shows the oil pressure
in either kilopascals (kPa) or pounds
per square inch (psi).

Engine Hours

Press the vehicle information button
until ENGINE HOURS displays. This
display shows the total number of
hours the engine has run.

Compass Zone Setting

This display allows for setting the
compass zone. See

Compass on

page 5

‑

6

for more information.

Compass Recalibration

This display allows for calibrating
the compass. See

Compass on

page 5

‑

6

for more information.

Blank Display

This display shows no information.

Trip Odometer Reset Stem
Menu Items (with DIC Buttons)

Use the trip odometer reset stem to
view the odometer and trip
odometer. The Language selection
and Engine Hours display can also
be accessed with the trip odometer
reset stem.

Odometer

Press the trip odometer reset stem
until ODOMETER displays. This
display shows the distance the
vehicle has been driven in either
kilometers (km) or miles (mi).

Trip Odometer

Press the trip odometer reset stem
until TRIP displays. This display
shows the current distance
traveled in either kilometers (km)
or miles (mi) since the last reset for
the trip odometer.

The trip odometer can be reset to
zero by pressing and holding the trip
odometer reset stem while the trip
odometer is displayed.

«
...
185
186
187
188
189
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: AC Schnitzer Pages: 16

Brand: Ranger design Pages: 6

Brand: JAC Pages: 70

Brand: Ultra Start Pages: 8

Brand: Roav Pages: 10

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: Opel Pages: 254

Brand: ORA Pages: 7

Brand: Lexus Pages: 830

Brand: Ranger design Pages: 22

2010 Accord Coupe

Brand: Honda Pages: 410

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Brand: MacNeil Pages: 2

Auto-Dimming Mirror

Brand: Mazda Pages: 2

Brand: Gator Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands