Chevrolet silverado 2012 Owner'S Manual Download Page 150

Page: 150 / 608

Black plate (2,1)

Chevrolet Silverado Owner Manual - 2012

5-2

Instruments and Controls

Transmission Messages . . . . . 5-51
Vehicle Reminder

Messages . . . . . . . . . . . . . . . . . . 5-51

Washer Fluid Messages . . . . . 5-52

Vehicle Personalization

Vehicle Personalization (With

DIC Buttons) . . . . . . . . . . . . . . . 5-52

Universal Remote System

Universal Remote System . . . 5-61
Universal Remote System

Programming . . . . . . . . . . . . . . . 5-62

Universal Remote System

Operation . . . . . . . . . . . . . . . . . . 5-67

Controls

Steering Wheel
Adjustment

The tilt lever is located on the lower
left side of the steering column.

To adjust the steering wheel:

1. Hold the steering wheel and pull

the lever.

2. Move the steering wheel up

or down.

3. Release the lever to lock the

wheel in place.

Do not adjust the steering wheel
while driving.

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for silverado 2012

Reviews:

Related manuals for silverado 2012

Brands by name

Popular brands

Chevrolet silverado 2012, Owner'S Manual

Search results

Summary of Contents for silverado 2012

Reviews:

Related manuals for silverado 2012

Brands by name

Popular brands