Chevrolet silverado 2012 Owner'S Manual Download Page 520 | Manualshive

Page: 520 / 608

background image

Black plate (96,1)

Chevrolet Silverado Owner Manual - 2012

10-96

Vehicle Care

Jump Starting

For more information about the
vehicle battery, see

Battery on

page 10

‑

33

.

If the vehicle is a hybrid, see the
hybrid supplement for more
information.

If the vehicle's battery (or batteries)
has run down, you may want to use
another vehicle and some jumper
cables to start your vehicle. Be sure
to use the following steps to do it
safely.

{

WARNING

Batteries can hurt you. They can
be dangerous because:

.

They contain acid that can
burn you.

.

They contain gas that can
explode or ignite.

.

They contain enough
electricity to burn you.

If you do not follow these steps
exactly, some or all of these
things can hurt you.

Notice:

Ignoring these steps

could result in costly damage to
the vehicle that would not be
covered by the warranty.

Trying to start the vehicle by
pushing or pulling it will not
work, and it could damage the
vehicle.

1. Check the other vehicle. It must

have a 12-volt battery with a
negative ground system.

Notice:

Only use a vehicle that

has a 12-volt system with a
negative ground for jump
starting. If the other vehicle does
not have a 12-volt system with a
negative ground, both vehicles
can be damaged.

2. If you have a vehicle with a

diesel engine with two batteries,
you should know before you
begin that, especially in cold
weather, you may not be able to
get enough power from a single
battery in another vehicle to start
your diesel engine. If your
vehicle has more than one
battery, using the battery that is
closer to the starter will reduce
electrical resistance. This is
located on the passenger side,
in the rear of the engine
compartment.

«
...
518
519
520
521
522
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Fabbri Pages: 4

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: ULTIMATE SPEED Pages: 50

Brand: Hudson Pages: 34

Brand: Jaeger Pages: 11

Brand: Kia Pages: 680

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brand: Audi Pages: 4

Brand: Pyle Pages: 14

Brand: AUTOTECH Pages: 2

Brand: Menabo Pages: 4

FUEL TANK GAUGE

Brand: VDO Pages: 10

Dual Clamp Spare Tire Mount

Brand: FACTORY UTV Pages: 2

Brand: Brodit Pages: 2

ELECTRONIC SPEEDOMETER 1323

Brand: VDO Pages: 2

Brand: Malone Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands