manualshive.com logo in svg

Chevrolet silverado 2012, Owner'S Manual

The Chevrolet Silverado 2012 Owner's Manual is a comprehensive guide designed to assist owners in understanding their truck's features and maintenance procedures. This essential manual provides detailed instructions and information, and it is available for free download at manualshive.com. Get yours today and empower yourself with the knowledge to maximize your Silverado's performance.

Share
Download
background image

Black plate (51,1)

Chevrolet Silverado Owner Manual - 2012

Instruments and Controls

5-51

to those shown on the Tire Loading
Information label. See

Tires on

page 10

‑

57

,

Vehicle Load Limits on

page 9

‑

17

, and

Tire Pressure on

page 10

‑

65

. The DIC also shows

the tire pressure values. See

Driver

Information Center (DIC) on
page 5

‑

33

.

Transmission Messages

SERVICE 4 WHEEL DRIVE

If the vehicle has four-wheel drive,
this message may display if a
problem occurs with the
four-wheel-drive system. If this
message appears, stop as soon as
possible and turn off the vehicle.
Make sure the key is in the LOCK/
OFF position for at least one minute
and then restart the vehicle and
check for the message on the DIC
display. If the message is still
displayed or appears again when
you begin driving, the
four-wheel-drive system needs
service. See your dealer.

TRANSMISSION HOT IDLE
ENGINE

Notice:

If you drive the vehicle

while the transmission fluid is
overheating and the transmission
temperature warning is displayed
on the instrument panel cluster
and/or DIC, you can damage the
transmission. This could lead to
costly repairs that would not be
covered by the warranty. Do not
drive the vehicle with overheated
transmission fluid or while the
transmission temperature
warning is displayed.

This message displays and a chime
may sound if the transmission fluid
in the vehicle gets hot. Driving with
the transmission fluid temperature
high can cause damage to the
vehicle. Stop the vehicle and let it
idle to allow the transmission to
cool. This message clears and the
chime stops when the fluid
temperature reaches a safe level.

Vehicle Reminder
Messages

CHECK TRAILER WIRING

On vehicles with the Integrated
Trailer Brake Control (ITBC) system,
this message may display and a
chime may sound when one of the
following conditions exists:

.

A trailer with electric brakes
becomes disconnected from the
vehicle.

‐

If the disconnect occurs while
the vehicle is stopped, this
message clears itself after a
short time.

‐

If the disconnect occurs while
the vehicle is moving, this
message stays on until the
ignition is turned off.

.

There is a short in the wiring to
the electric trailer brakes.

When this message displays, power
is no longer available to the trailer
brakes.

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Brand: Federal Signal Corporation Pages: 13
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Brand: VEAP SHIELD UNITED Pages: 3
Tamiya KO PROPO RTF 2002 ESC Manual preview
KO PROPO RTF 2002 ESC
Brand: Tamiya Pages: 2
FVC Sprinter Bed System Adventure Wagon Kit Installation Manual preview
Sprinter Bed System Adventure Wagon Kit
Brand: FVC Pages: 8
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Brand: Roadmaster Pages: 12
Velleman CAMCOLC1N User Manual preview
CAMCOLC1N
Brand: Velleman Pages: 6
V8 equipment EBEX.2 Instruction Manual preview
EBEX.2
Brand: V8 equipment Pages: 17
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Brand: Xpresskit Pages: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Brand: RAM Pages: 92
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Brand: Honda Pages: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Brand: Kia Pages: 219
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Brand: Dodge Pages: 5
Edelbrock 65932 Installation Instructions preview
65932
Brand: Edelbrock Pages: 2
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Brand: Mercedes-Benz Pages: 39
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Brand: Cadillac Pages: 529
Toro 07389 Installation Instructions Manual preview
07389
Brand: Toro Pages: 16
Mazda 323F Owner'S Manual preview
323F
Brand: Mazda Pages: 196
Skoda Octavia 2007 Owner'S Manual preview
Octavia 2007
Brand: Skoda Pages: 288

Brands by name

Popular brands

Load more brands