Chevrolet silverado 2012 Owner'S Manual Download Page 183 | Manualshive

Page: 183 / 608

background image

Black plate (35,1)

Chevrolet Silverado Owner Manual - 2012

Instruments and Controls

5-35

Trip/Fuel Menu Items (with DIC
Buttons)

3

(Trip/Fuel):

Press this button

to scroll through the following menu
items:

Odometer

Press the trip/fuel button until
ODOMETER displays. This display
shows the distance the vehicle has
been driven in either kilometers (km)
or miles. Pressing the trip odometer
reset stem will also display the
odometer.

To switch between metric and
English measurements, see

“

Units

”

later in this section.

Trip Odometer

Press the trip/fuel button until TRIP
displays. This display shows the
current distance traveled in either
kilometers (km) or miles since the
last reset for the trip odometer.
Pressing the trip odometer reset
stem will also display the trip
odometer.

The trip odometer can be reset to
zero by pressing the set/reset
button while the trip odometer is
displayed. You can also reset the
trip odometer while it is displayed by
pressing and holding the trip
odometer reset stem.

The trip odometer has a feature
called the retro-active reset. This
can be used to set the trip odometer
to the number of miles (kilometers)
driven since the ignition was last
turned on. This can be used if the
trip odometer is not reset at the
beginning of the trip.

To use the retro-active reset feature,
press and hold the set/reset button
for at least four seconds. The trip
odometer will display the number of
kilometers (km) or miles driven since
the ignition was last turned on and
the vehicle was moving. Once the
vehicle begins moving, the trip
odometer will accumulate mileage.

For example, if the vehicle was
driven 8 km (5 miles) before it is
started again, and then the
retro-active reset feature is
activated, the display will show 8 km
(5 miles). As the vehicle begins
moving, the display will then
increase to 8.2 km (5.1 miles),
8.4 km (5.2 miles), etc.

Fuel Range

Press the trip/fuel button until FUEL
RANGE displays. This display
shows the approximate number of
remaining kilometers (km) or miles
the vehicle can be driven without
refueling. The display will show
LOW if the fuel level is low.

«
...
181
182
183
184
185
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Accel Pages: 2

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Intercooler Kit Type 31

Brand: GReddy Pages: 9

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: AA Products Pages: 4

Brand: Hudson Pages: 34

Brand: PEUGEOT Pages: 17

Brand: Ford Pages: 52

Brand: Enduro Pages: 52

Brand: Whispbar Pages: 15

Brand: Hyundai Pages: 168

Brand: Speedtech Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands