Chevrolet silverado 2012 Owner'S Manual Download Page 332 | Manualshive

Page: 332 / 608

background image

Black plate (32,1)

Chevrolet Silverado Owner Manual - 2012

9-32

Driving and Operating

When the fast idle is active the
Driver Information Center (DIC) will
display

“

FAST IDLE ON.

”

One of the following actions will turn
off the fast idle:

.

Pressing the brake.

.

Selecting the Cruise Control
Cancel button.

.

Releasing the Parking Brake.

.

The transmission shift lever is
moved out of P (Park) or
N (Neutral).

.

Selecting the Cruise Control On/
Off button when it was
previously on.

.

Pressing the Cruise Control Set
switch a second time.

.

Pressing the accelerator greater
than a quarter of the way down.

.

Turning the ignition switch to the
LOCK/OFF position.

Retained Accessory
Power (RAP)

The following vehicle accessories
can be used for up to 10 minutes
after the engine is turned off:

.

Audio System

.

Power Windows

.

OnStar System (if equipped)

.

Sunroof (if equipped)

These features work when
the key is in ON/RUN or ACC/
ACCESSORY. Once the key is
turned from ON/RUN to LOCK/OFF,
the windows and sunroof continue
to work up to 10 minutes until any
door is opened. The radio continues
to work for up to 10 minutes or until
the driver door is opened.

Engine Coolant Heater

The engine heater can provide
easier starting and better fuel
economy during engine warm-up in
cold weather conditions at or
below

−

18°C (0°F). Vehicles with an

engine heater should be plugged in
at least four hours before starting.
An internal thermostat in the
plug-end of the cord may exist
which will prevent engine coolant
heater operation at temperatures
above

−

18°C (0°F).

If the vehicle has a diesel engine,
see the Duramax Diesel supplement
for more information.

«
...
330
331
332
333
334
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Davis Instruments Pages: 16

Brand: PAC Pages: 15

Green Motion Building

Brand: Eaton Pages: 12

Brand: FormFit Pages: 2

Brand: TATA Motors Pages: 236

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

Hatch-bag Luggage System

Brand: Tabernus Peram Pages: 10

Brand: Mopar Pages: 18

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Tipper Remote Kit

Brand: Nugent Pages: 21

Brand: Gator Pages: 5

Brand: Kargo Master Pages: 8

Brand: Truma Pages: 84

Brand: CAME Pages: 14

IREESE TACTICAL 70894

Brand: Horizon Global Pages: 3

LiftMaster Professional 975LMC

Brand: Chamberlain Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands