Chevrolet silverado 2012 Owner'S Manual Download Page 448 | Manualshive

Page: 448 / 608

background image

Black plate (24,1)

Chevrolet Silverado Owner Manual - 2012

10-24

Vehicle Care

3. Fill the coolant surge tank with

the proper mixture to the FULL
COLD mark.

4. With the coolant surge tank

pressure cap off, start the
engine and let it run until the
engine coolant temperature
gauge indicates approximately
90°C (195°F).

By this time, the coolant level
inside the coolant surge tank
may be lower. If the level is
lower, add more of the proper
mixture to the coolant surge tank
until the level reaches the FULL
COLD mark.

5. Replace the pressure cap. Be

sure the pressure cap is
hand-tight and fully seated.

6. Verify coolant level after the

engine is shut off and the
coolant is cold. If necessary,
repeat coolant fill procedure
Steps 1 through 6.

Notice:

If the pressure cap is not

tightly installed, coolant loss and
possible engine damage may
occur. Be sure the cap is properly
and tightly secured.

Engine Overheating

If the vehicle has the Duramax

®

Diesel engine, see the Duramax
Diesel Supplement for more
information.

The vehicle has several indicators
to warn of engine overheating.

There is a coolant temperature
gauge on the vehicle's instrument
panel. See

Engine Coolant

Temperature Gauge on page 5

‑

17

.

In addition, there are ENGINE
OVERHEATED STOP ENGINE,
ENGINE OVERHEATED IDLE
ENGINE, and ENGINE POWER IS
REDUCED messages in the Driver
Information Center (DIC) on the
instrument panel. See

Engine

Cooling System Messages on
page 5

‑

45

and

Engine Power

Messages on page 5

‑

47

.

«
...
446
447
448
449
450
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: B-Speech Pages: 24

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Brand: AA Products Pages: 4

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brand: TATA Motors Pages: 92

HU-4421-XL-SDK01

Brand: FALCON RIDGE Pages: 5

Brand: Vangear Pages: 5

Brand: Safe Fleet Pages: 20

Brand: Subaru Pages: 2

Brand: Subaru Pages: 786

Brand: Bazooka Pages: 2

Dual Clamp Spare Tire Mount

Brand: FACTORY UTV Pages: 2

Brand: Seecode Pages: 19

Brand: Axxess Pages: 16

Brand: Axxess Pages: 8

Brand: Datsun Pages: 386

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands