Chevrolet silverado 2012 Owner'S Manual Download Page 363 | Manualshive

Page: 363 / 608

background image

Black plate (63,1)

Chevrolet Silverado Owner Manual - 2012

Driving and Operating

9-63

Parking Brake

For vehicles with a release handle,
set the parking brake by holding the
regular brake pedal down, then
pushing down the parking brake
pedal.

If the ignition is on, the brake
system warning light will come on.
See

Brake System Warning Light on

page 5

‑

27

.

A chime sounds and the warning
light flashes when the parking brake
is applied and the vehicle is moving
at least 8 km/h (5 mph).

To release the parking brake, hold
the regular brake pedal down. Then
pull the bottom edge of the lever
with the parking brake symbol,
located above the parking brake
pedal.

If the ignition is on when the parking
brake is released, the brake system
warning light goes off.

Notice:

Driving with the parking

brake on can overheat the brake
system and cause premature
wear or damage to brake system
parts. Make sure that the parking
brake is fully released and the
brake warning light is off before
driving.

If you are towing a trailer and are
parking on any hill, see

Driving

Characteristics and Towing Tips on
page 9

‑

86

.

For vehicles without a release
handle, set the parking brake by
holding the regular brake pedal
down, then pushing down the
parking brake pedal.

«
...
361
362
363
364
365
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: JETBAG Pages: 44

Titanium Series

Brand: Fass Pages: 13

2011 grand cherokee

Brand: Jeep Pages: 22

2013 Grand Cherokee

Brand: Jeep Pages: 704

Brand: Jeep Pages: 558

2011 Corolla LE

Brand: Toyota Pages: 19

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Nav TV Pages: 3

Brand: Toro Pages: 24

Brand: Tachosys Pages: 28

Truck Training Model

Brand: WABCO Pages: 56

Electra 225 1965

Brand: Buick Pages: 914

Brand: Volvo Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands