Chevrolet silverado 2012 Owner'S Manual Download Page 582 | Manualshive

Page: 582 / 608

background image

Black plate (20,1)

Chevrolet Silverado Owner Manual - 2012

13-20

Customer Information

Current and Past Models

Technical Service Bulletins and
Manuals are available for current
and past model GM vehicles.

ORDER TOLL FREE:
1-800-551-4123 Monday

–

Friday

8:00 AM

–

6:00 PM Eastern Time

For Credit Card Orders Only
(VISA-MasterCard-Discover), visit
Helm, Inc. at: www.helminc.com.

Or write to:

Helm, Incorporated
Attention: Customer Service
47911 Halyard Drive
Plymouth, MI 48170

Prices are subject to change without
notice and without incurring
obligation. Allow ample time for
delivery.

All listed prices are quoted in U.S.
funds. Make checks payable in U.S.
funds.

Reporting Safety
Defects

Reporting Safety Defects
to the United States
Government

If you believe that your vehicle
has a defect which could cause
a crash or could cause injury or
death, you should immediately
inform the National Highway
Traffic Safety Administration
(NHTSA) in addition to notifying
General Motors.

If NHTSA receives similar
complaints, it may open an
investigation, and if it finds that
a safety defect exists in a group
of vehicles, it may order a recall
and remedy campaign.
However, NHTSA cannot
become involved in individual
problems between you, your
dealer, or General Motors.

To contact NHTSA, you may call
the Vehicle Safety Hotline
toll-free at 1-888-327-4236
(TTY: 1-800-424-9153); go to

http://www.safercar.gov;

or

write to:

Administrator, NHTSA
1200 New Jersey Avenue, S.E.
Washington, D.C. 20590

You can also obtain other
information about motor
vehicle safety from

http://www.safercar.gov

.

«
...
580
581
582
583
584
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: TATA Motors Pages: 159

Brand: Porsche Pages: 313

Brand: Axxess Pages: 8

Brand: Dodge Pages: 276

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: Ranger design Pages: 24

Brand: cam Pages: 28

Brand: Rugged Ridge Pages: 3

Brand: Honda Pages: 124

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Brand: HAKR Pages: 9

Charger SRT 392 2017

Brand: Dodge Pages: 576

Brand: Lexus Pages: 108

Brand: CARFACE Pages: 16

TOUR EASY 4 936550

Brand: Reimo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands