Chevrolet silverado 2012 Owner'S Manual Download Page 433 | Manualshive

Page: 433 / 608

background image

Black plate (9,1)

Chevrolet Silverado Owner Manual - 2012

Vehicle Care

10-9

Selecting the Right Engine Oil

Selecting the right engine oil
depends on both the proper oil
specification and viscosity grade.
See

Recommended Fluids and

Lubricants on page 11

‑

13

.

Specification

Use and ask for licensed engine oils
with the dexos1

™

approved

certification mark. Engine oils
meeting the requirements for the
vehicle should have the dexos

™

1

approved certification mark. This
certification mark indicates that the
oil has been approved to the dexos1
specification.

Notice:

Failure to use the

recommended engine oil or
equivalent can result in engine
damage not covered by the
vehicle warranty. Check with your
dealer or service provider on
whether the oil is approved to the
dexos1 specification.

Viscosity Grade

SAE 5W

‐

30 is the best viscosity

grade for the vehicle. Do not use
other viscosity grade oils such as
SAE 10W

‐

30, 10W

‐

40, or 20W

‐

50.

If in an area of extreme cold, where
the temperature falls below

−

20°F

(

−

29°C), an SAE 0W

‐

30 oil should

be used. An oil of this viscosity
grade will provide easier cold
starting for the engine at extremely
low temperatures. When selecting
an oil of the appropriate viscosity
grade, always select an oil that
meets the dexos1 specification or
equivalent. See

“

Specification

”

for

more information.

Engine Oil Additives/Engine
Oil Flushes

Do not add anything to the oil. The
recommended oils with the dexos
specification and displaying the
dexos certification mark are all that
is needed for good performance and
engine protection.

Engine oil system flushes are not
recommended and could cause
engine damage not covered by the
vehicle warranty.

«
...
431
432
433
434
435
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: Harbor Freight Tools Pages: 4

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Ford Pages: 52

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: Magneti Marelli Pages: 2

Brand: Carcomm Pages: 2

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

TuneBase F8Z442

Brand: Belkin Pages: 162

Brand: Mercedes-Benz Pages: 305

S90 TWIN ENGINE

Brand: Volvo Pages: 662

Brand: Kuda Pages: 3

Brand: Easee Pages: 21

Brand: Tesla Pages: 42

Brand: SIXTOL Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands