Chevrolet silverado 2012 Owner'S Manual Download Page 186 | Manualshive

Page: 186 / 608

background image

Black plate (38,1)

Chevrolet Silverado Owner Manual - 2012

5-38

Instruments and Controls

When the remaining oil life is low,
the CHANGE ENGINE OIL SOON
message will appear on the display.
See

“

CHANGE ENGINE OIL SOON

”

under

Engine Oil Messages on

page 5

‑

46

. You should change the

oil as soon as you can. See

Engine

Oil on page 10

‑

7

. In addition to the

engine oil life system monitoring the
oil life, additional maintenance is
recommended in the Maintenance
Schedule in this manual. See

Maintenance Schedule on
page 11

‑

3

for more information.

Remember, you must reset the OIL
LIFE display after each oil change.
It will not reset itself. Also, be
careful not to reset the OIL LIFE
display accidentally at any time
other than when the oil has just
been changed. It cannot be reset
accurately until the next oil change.
To reset the engine oil life system,
see

Engine Oil Life System on

page 10

‑

10

.

Units

Press the vehicle information button
until UNITS displays. This display
allows you to select between metric
or English units of measurement.
Once in this display, press the set/
reset button to select between
METRIC or ENGLISH units.
All of the vehicle information will
then be displayed in the unit of
measurement selected.

Tire Pressure

If the vehicle has the Tire Pressure
Monitor System (TPMS), the
pressure for each tire can be viewed
in the DIC. The tire pressure will be
shown in either kilopascals (kPa) or
pounds per square inch (psi). Press
the vehicle information button
until the DIC displays FRONT
TIRES kPa (PSI) LEFT ##
RIGHT ##. Press the vehicle
information button again until the
DIC displays REAR TIRES kPa
(PSI) LEFT ## RIGHT ##.

If a low tire pressure condition is
detected by the system while
driving, a message advising you to
add pressure in a specific tire will
appear in the display. See

Tire

Pressure on page 10

‑

65

and

Tire

Messages on page 5

‑

50

for more

information.

If the tire pressure display shows
dashes instead of a value, there
may be a problem with the vehicle.
If this consistently occurs, see your
dealer for service.

Trailer Gain and Output

On vehicles with the Integrated
Trailer Brake Control (ITBC) system,
the trailer brake display appears in
the DIC. Press the vehicle
information button until TRAILER
GAIN and OUTPUT display.

TRAILER GAIN shows the trailer
gain setting. This setting can be
adjusted from 0.0 to 10.0 with either
a trailer connected or disconnected.

«
...
184
185
186
187
188
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: iDataLink Pages: 9

Brand: JETBAG Pages: 44

Brand: Toyota Pages: 529

Brand: Feniex Pages: 6

Brand: kaarta Pages: 29

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

Brand: Kia Pages: 419

Brand: Thule Pages: 8

Brand: AC Schnitzer Pages: 20

Brand: ULTIMATE SPEED Pages: 21

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brand: Power Acoustik Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands