Chevrolet silverado 2012 Owner'S Manual Download Page 364 | Manualshive

Page: 364 / 608

background image

Black plate (64,1)

Chevrolet Silverado Owner Manual - 2012

9-64

Driving and Operating

If the ignition is on, the brake
system warning light will come on.
See

Brake System Warning Light on

page 5

‑

27

.

Notice:

Driving with the parking

brake on can overheat the brake
system and cause premature
wear or damage to brake system
parts. Make sure that the parking
brake is fully released and the
brake warning light is off before
driving.

To release the parking brake, hold
the regular brake pedal down, then
push down momentarily on the
parking brake pedal until you feel
the pedal release. Slowly pull your
foot up off the park brake pedal.

If the parking brake is not released
when you begin to drive, the brake
system warning light will flash and a
chime will sound warning you that
the parking brake is still on.

If you are towing a trailer and are
parking on a hill, see

Driving

Characteristics and Towing Tips on
page 9

‑

86

.

Brake Assist

If this vehicle has StabiliTrak

®

, it

also has a Brake Assist feature
designed to assist the driver in
stopping or decreasing vehicle
speed in emergency driving
conditions. This feature uses the
stability system hydraulic brake
control module to supplement the
power brake system under
conditions where the driver has

quickly and forcefully applied the
brake pedal in an attempt to quickly
stop or slow down the vehicle. The
stability system hydraulic brake
control module increases brake
pressure at each corner of the
vehicle until the ABS activates.
Minor brake pedal pulsation or
pedal movement during this time is
normal and the driver should
continue to apply the brake pedal as
the driving situation dictates The
Brake Assist feature will
automatically disengage when the
brake pedal is released or brake
pedal pressure is quickly
decreased.

«
...
362
363
364
365
366
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: AA Products Pages: 8

Brand: Garmin Pages: 2

Brand: Kolpin Pages: 25

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Porsche Pages: 195

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: MAXWORKS Pages: 7

Brand: Nav TV Pages: 3

Brand: Metra Electronics Pages: 20

Brand: CALIMA Pages: 9

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: BrandMotion Pages: 6

Brand: TAUBENREUTHER Pages: 18

MagicSpeed MS900

Brand: Waeco Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands