Chevrolet silverado 2012 Owner'S Manual Download Page 333 | Manualshive

Page: 333 / 608

background image

Black plate (33,1)

Chevrolet Silverado Owner Manual - 2012

Driving and Operating

9-33

To Use the Engine Coolant
Heater

1. Turn off the engine.

2. Open the hood and unwrap the

electrical cord. The cord is
secured to the Engine
Compartment Fuse Block with a
clip. Carefully remove the wire
tie which bundles the electrical
plug. Do not cut the
electrical cord.

3. Plug the cord into a normal,

grounded 110-volt AC outlet.

{

WARNING

Plugging the cord into an
ungrounded outlet could cause an
electrical shock. Also, the wrong
kind of extension cord could
overheat and cause a fire. You
could be seriously injured. Plug
the cord into a properly grounded
three-prong 110-volt AC outlet.
If the cord will not reach, use a
heavy-duty three-prong extension
cord rated for at least 15 amps.

4. Before starting the engine, be

sure to unplug and store the
cord as it was before to keep it
away from moving engine parts.
If you do not, it could be
damaged.

The length of time the heater should
remain plugged in depends on
several factors. Ask a dealer in the
area where you will be parking the
vehicle for the best advice on this.

«
...
331
332
333
334
335
...
»

Summary of Contents for silverado 2012

































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for silverado 2012

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: UltraGauge Pages: 55

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: Honda Pages: 4

SAFESTOP SS0005

Brand: Pro-gard Pages: 4

Calispace Ocean 80

Brand: Calitop Pages: 5

Brand: E&G Classics Pages: 4

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: NavLinkz Pages: 23

Brand: Mont Blanc Pages: 2

Brand: Flash Cover Pages: 2

Brand: SpeedTech Lights Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands