Cerio OW-200N2 User Manual Download Page 55

Page: 55 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

2.4.3

Configure UPnP

Universal Plug and Play(UPnP) is an architecture to enable pervasive peer-to-peer network connectivity between

PCs, intelligent devices and appliances when UPnP is supported. UPnP works on TCP/IP network to enable UPnP

devices to connect and access to each other, very well adopted in home networking environment.

UPnP :

By default, it’s “

Disable

”. Select “

Enable

” or “

Disable”

of UPnP Service.

Click

Save

button to save changes and click

Reboot

button to activate changes

For UPnP to work in Windows XP, the “OW-200N2” must be available in “

My Network Places

”

, as shown here: (your

specific model may vary)

If these devices are not available, you should verify that the correct components and services are loaded in Windows

XP. Please refer to

Appendix E. Using UPnP on Windows XP

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands