Cerio OW-200N2 User Manual Download Page 188

Page: 188 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

188

correct MTU setting.

MPPE Encryption :

Microsoft Point-to-Point Encryption (MPPE) encrypts data in Point-to-Point

Protocol(PPP)-based dial-up connections or Point-to-Point Tunneling Protocol (PPTP) virtual private

network (VPN) connections.

128

bit

key (strong) and

bit

key (standard) MPPE encryption schemes

are supported. MPPE provides data security for the PPTP connection that is between the VPN client

and the VPN server.

DNS :

Check “No Default DNS Server” or “Specify DNS Server IP” radial button as desired to set up system

DNS.

Primary :

The IP address of the primary DNS server.

Secondary :

The IP address of the secondary DNS server.

In this mode, the system does not support MAC Clone function.

Click

Save

button to save your changes. Click

Reboot

button to activate your changes

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands