Cerio OW-200N2 User Manual Download Page 220

Page: 220 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

220

7.4.4

Configure SNMP Setup

SNMP is an application-layer protocol that provides a message format for communication between SNMP managers

and agents. By enabling SNMP function, the administrator can obtain the system information remotely.

Please click on

System -> SNMP Setup

and follow the below setting.

SNMP v2c Enable:

Check to enable SNMP v2c.

ro community :

Set a community string to authorize read-only access.

rw community :

Set a community string to authorize read/write access.

SNMP v3 Enable:

Check to enable SNMP v3.

SNMPv3 supports the highest level SNMP security.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands