Cerio OW-200N2 User Manual Download Page 222

Page: 222 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

222

7.4.5

Backup / Restore and Reset to Factory

Backup current configuration, restore prior configuration or reset back to factory default configuration can be

executed via this page.

Please click on

Utilities -> Profile Setting

and follow the below setting.

Save Settings to PC :

Click

Save

button to save the current configuration to a local disk.

Load Settings from PC :

Click

Browse

button to locate a configuration file to restore, and then click

Upload

button to upload.

Reset To Factory Default :

Click

Default

button to reset back to the factory default settings and expect

Successful

loading message

Then, click

Reboot

button to activate.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands