Cerio OW-200N2 User Manual Download Page 114

Page: 114 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

114

4.2.1.2

Dynamic IP

: This configuration type is applicable when the OW-200N2is

connected to a network with the presence of a DHCP server; all related IP
information will be provided by the DHCP server automatically.

Hostname

: The Hostname of the LAN port.

4.2.1.3

DNS

: Check either “

No Default DNS Server

” or “

Specify DNS Server IP

”

button as desired to set up the system DNS.

Primary

: The IP address of the primary DNS server.

Secondary

: The IP address of the secondary DNS server.

4.2.1.4

802.1d Spanning Tree

The spanning tree network protocol provides a loop free topology for a bridged
LAN between LAN interface and 8 WDS interfaces from wds0 to wds7. The
Spanning Tree Protocol, which is also referred to as STP, is defined in the IEEE
Standard 802.1d.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands