Cerio OW-200N2 User Manual Download Page 78

Page: 78 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

MAC Address :

MAC addresses of LAN devices.

Expired In :

Shows how long the leased IP address will expire.

2.7.2

Associated Clients Status

It displays ESSID, on/off Status, Security Type, total number of wireless clients associated with all Virtual AP.

VAP Information :

Highlights key VAP information.

VAP :

Available VAP from Primary AP to VAP6.

ESSID :

Display name of ESSID for each VAP.

MAC Address :

Display MAC address for each VAP.

Status :

On/Off

Security Type :

Display chosen security type; WEP, WPA/WPA2-PSK, WPA/WPA2-Enterprise.

Clients :

Display total number of wireless connections for each VAP.

VAP Clients :

Display all associated clients on each Virtual AP.

MAC Address :

MAC address of associated clients

Signal Strength ANT0/ANT1 :

Signal Strength of from associated clients.

Bandwidth :

Channel bandwidth of from associated clients

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands