Cerio OW-200N2 User Manual Download Page 283

Page: 283 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

283

Appendix D. System Manager Privileges

There are two system management accounts for maintaining the system; namely, the

root

and

admin

accounts are

with different levels of privileges. The root manager account is empowered with full privilege to Read & Write while the

admin manager account is Read only.

The following table display CPE admin account’s privileges.

Main Menu

Sub Menu

Group

Admin Privilege

Operating Mode

Read

WAN

Read

LAN

Read & Write

DDNS

Read & Write

Time Server

Read & Write

UPNP

Read & Write

System

SNMP

Read

General

Read

Advanced

Read

Wireless

Site Survey

Read

DMZ

Read

IP Filter

Read

MAC Filter

Read

Virtual Server

Read

Parental Control

Read

Advance

QoS

Read

System Information

Read

Root Password

Read

Admin Password

Read & Write

Administrator

Management

Read

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands