Cerio OW-200N2 User Manual Download Page 265

Page: 265 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

265

10.1.2

Network Information

: Supports Static or Dynamic modes on the LAN interface.

10.1.2.1

IP Address

: The management IP of system. By default, it’s

192.168.2.254.

10.1.2.2

IP Netmask

: The network mask. By default, it’s 255.255.255.0.

10.1.2.3

IP Gateway

: The gateway IP address and by default, it’s 192.168.2.1.

10.1.2.4

Primary DNS

: The primary DNS server in service.

10.1.2.5

Secondary DNS

: The secondary DNS server in service.

10.1.3

LAN Information

: Display total received and transmitted statistics on the LAN

interface.

10.1.3.1

MAC Address

: The MAC address of the LAN port.

10.1.3.2

Receive bytes

: The total received packets in bytes on the LAN port.

10.1.3.3

Receive packets

: The total received packets of the LAN port.

10.1.3.4

Transmit bytes

: The total transmitted packets in bytes of the LAN port.

10.1.3.5

Transmit packets

: The total transmitted packets of the LAN port.

10.1.4

Wireless Information

: Display total received and transmitted statistics on available

Virtual AP.

10.1.4.1

MAC Address

: The MAC address of the Wireless port.

10.1.4.2

Receive bytes

:The total received packets in bytes on the Wireless port.

10.1.4.3

Receive packets

: The total received packets on the Wireless port.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands