Cerio OW-200N2 User Manual Download Page 71

Page: 71 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

2.6 Resource Sharing

2.6.1

DMZ

DMZ is commonly work with the NAT functionality as an alternative of Virtual Server(Port Forwarding

)

while wanting

all ports of DMZ host visible to Internet users. Virtual Server rules have precedence over the DMZ rule. In order to use

a range of ports available to access to different internal hosts Virtual Server rules are needed.

Please click on

Advance -> DMZ

and follow the below setting.

DMZ :

By default, it’s

“

Disable

”.

Check

Enable

radial button to enable DMZ.

IP Address :

Enter IP address of DMZ host and only one DMZ host is supported.

Click

Save

button to save your changes. Click

Reboot

button to activate your changes.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands