Cerio OW-200N2 User Manual Download Page 17

Page: 17 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

Panel Function Description

There is several LED indicators on the front of the OW-200N2. Please refer to the
definitions below :

Front Panel

Rear Panel

1.6.4.11

Reboot Button

: Unscrew the screw and click Reset button to restart

system or reset to default configurations, Press and hold the Reset button for
more than 20 seconds to reset the system to default configurations.

1.6.4.12

Power

: Green LED ON indicates power on, and OFF indicates power off.

1.6.4.13

WLAN

: Green LED FLASH indicates Wireless Transmit.

1.6.4.14

Ethernet

: Green LED ON indicates connection, OFF indicates no

connection, FLASH indicates Packets transmit.

1.6.4.15

PoE Connector

: For connecting to PSE.

1.6.4.16

N-Type Connector

: you can connect N-type antenna here.

1.7 Hardware Installation Steps

Please follow the steps mentioned below to install the hardware of OW-200N2

1.7.1.1

Connect N-type antenna to the N-type connector on the rear panel.

1.7.1.2

Connect PSE to the PoE connector on the front panel.

1.7.1.3

Connect an Ethernet cable to the PSE and the other end to a computer.

1.7.1.4

Power on the PSE in order to supply power to OW-200N2

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands