Cerio OW-200N2 User Manual Download Page 118

Page: 118 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

118

to radio-frequency reflections. Select the option that works best for your
installation.

4.3.3.4

MCS

: This parameter represents transmission rate. By default (Auto) the

fastest possible transmission rate will be selected. You have the option of
selecting the speed if necessary.

4.3.3.5

Reverse Direction Grant(RDG)

: Disable or enable reserve direction grant.

Default is enabled.

4.3.3.6

A-MSDU

: Aggregated Mac Service Data Unit. Select Enable to allow

aggregation for multiple MSDUs in one MPDU Default is disabled.

4.3.3.7

Auto Block ACK

: Disable or enable auto block ACK. Default is enabled.

4.3.3.8

Decline BA Request

: Disable or enable decline BA request. Default is

disabled.

Change these settings as described here and click

Save

button to save your

changes. Click

Reboot

button to activate your changes. The items in this page

are for AP's RF general settings and will be applied to all VAPs.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands