Cerio OW-200N2 User Manual Download Page 285

Page: 285 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

285

Appendix E. Enabling UPnP in Windows XP

1. Open

the

“

Add/Remove Programs

”

control panel, and then click on “

Add/Remove Windows Components

”

the sidebar. Scroll down and find “

Networking Services

”

, highlight it, and then click

Details

2. In the “

Networking Services

” window, ensure that the “

Internet Gateway Device

”

and “

UPnP User Interface

”

options are checked. If they are not, check it to enable them, as shown below, and click OK to continue.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands