Cerio OW-200N2 User Manual Download Page 208

Page: 208 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

208

Cipher Suite :

By default, it is

AES

. Select either AES or TKIP cipher suites

Pre-shared Key :

Enter the pre-shared key; the format shall go with the selected key type.

Pre-shared key can be entered with either a 256-bit secret in 64 HEX digits format, or 8 to 63 ASCII characters.

Group Key Update Period :

default, it is

3600

seconds. This time interval for rekeying GTK,

broadcast/multicast encryption keys, in seconds. Entering the time-length is required.

7.3.1.4

WPA-Enterprise (or WPA2-Enterprise):

The RADIUS authentication and encryption will

be both enabled if this is selected.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands