Cerio OW-200N2 User Manual Download Page 268

Page: 268 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

268

10.3 Show WDS Status

Peers MAC Address, antenna 0/1 received signal strength, phy mode and channel
bandwidth for each WDS are available.

10.3.1

MAC

: Display MAC address of WDS peer.

10.3.2

Signal Strength ANT0/ANT1

: Indicate the signal strength of the repective WDS

linkes.

10.3.3

Phy Mode

: Indicate the phy mode of the respective WDS linked.

10.3.4

BandWidth

: Indicate the channel bandwidth of the respective WDS linked.

If display “

no signal”

Signal Strength ANT0/ANT1, you need check WDS

configuration. Things to verify are

MAC Address,

Channel

and

Security type

Also, adjust antenna angle and Tx Power.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands