Cerio OW-200N2 User Manual Download Page 30

Page: 30 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

LAN IP :

The administrator can manually setup the LAN IP address.

IP Address :

The IP address of the LAN port; default IP address is 192.168.2.254

IP Netmask :

The Subnet mask of the LAN port; default Netmask is 255.255.255.0

DHCP Setup :

Devices connected to the system can obtain an IP address automatically when this service is

enabled.

DHCP :

Check

Enable

button to activate this function or

Disable

to deactivate this service.

Start IP / End IP:

Specify the range of IP addresses to be used by the DHCP server when assigning IP

address to clients. The default range IP address is 192.168.2.10 to 192.168.2.70, the netmask is

255.255.255.0

DNS1 IP :

Enter IP address of the first DNS server; this field is required.

DNS2 IP :

Enter IP address of the second DNS server; this is optional.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands