Cerio OW-200N2 User Manual Download Page 210

Page: 210 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

210

Radius Server Settings :

•

IP Address :

Enter the IP address of the Authentication RADIUS server.

•

Port :

By default, it’s

1812

The port number used to communicate with RADIUS server.

•

Shared secret :

A secret key used between system and RADIUS server. Supports

characters.

•

Session Timeout :

The Session timeout is in the range of

seconds

. The default is

disable re-authenticate service.

Amount of time before a client will be required to re-authenticate.

Change these settings as described here and click

Save

button to save your changes. Click

Reboot

button to

activate your changes

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands