Cerio OW-200N2 User Manual Download Page 75

Page: 75 / 290

User’s Manual

500mW eXtreme Power 11Na Outdoor Bridge

System Up Time :

The time period that system has been in service since last reboot.

WAN Information :

Display the information of the WAN interface.

The WAN port specified

Dynamic

, the Release and Renew button will be show-up, click

Release

button to

release IP address of

WAN port,

Renew

button to renew IP

address through DHCP server.

The WAN port specified

PPPoE

PPTP

, and the

Connect

and

DisConnect

button will be show up. Click

“

Connect

” button to assigned IP address from PPPoE or PPTP server, “

DisConnect

” button to release IP

address of WAN port.

Mode :

Supports Static, Dynamic, PPPoE and PPTP modes.

Summary of Contents for OW-200N2



































































































































































































































































































Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands

Cerio OW-200N2, User Manual

Search results

Summary of Contents for OW-200N2

Reviews:

Related manuals for OW-200N2

Brands by name

Popular brands