YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 90

Страница: 90 / 406

11-52

IM 701210-06E

Explanation

By setting the upper/lower limits of the automated measurement of waveform

parameters, GO/NO-GO determination is performed on whether the measured value

enters the range or exits the range.

Setting the Determination Conditions: Setup

• Selecting the Target Waveform: Trace

Select the waveform from CH1 to CH16, DSP1 to DSP6 (optional), and Math

waveforms.

• Setting the Determination Mode

OFF:

Does not perform GO/NO-GO determination.

IN:

Go condition when the value enters the specified upper and lower limits.

OUT:

Go condition when the value exits from the specified upper and lower limits.

• Selecting the Parameter: Item

The waveform parameters that can be used are all the items of automated

measurement of waveform parameters (28 types) given in section 11.6. Up to 16

types of parameters can be determined simultaneously.

• Setting the Upper and Lower Limits of Parameters

The upper and lower limits vary depending on the parameters. They can be set in the

range –9.9999E+30 to 9.9999E+30.

• Setting the Logic

AND:

Executes the action when all parameter conditions (1 to 16 types) are met.

OR:

Executes the action when any one of the parameter conditions (1 to 16 types)

is met.

• Action Condition: ActCondition

Always:

Always executes the action.

Failure:

Execute the action when the GO condition is not met.

Success:

Execute the action when the GO condition is met.

When Always is selected, the operation specified by Action is executed each time the

trigger occurs. This function is useful such as when you wish to print the screen

image data to a printer each time the trigger occurs.

• Setting the Number of Actions: Sequence

Single:

Performs the action once.

Continue: Repeats the action up to acquisition count specified by ACQ Count. (If the

count is set to Infinite, the action is repeated until the waveform acquisition

is stopped.)

• Setting the Number of Determinations: ACQ Count

Set the number of waveform acquisitions.

Infinite:

Continues until the waveform acquisition is stopped using the Abort soft

key or START/STOP.

1 to 65536: Stops when the specified number of waveforms is acquired.

• GO/NO-GO Determination Using an External Input Signal: Remote

GO/NO-GO determination can be performed by synchronizing to an external signal

applied to the GO/NO-GO I/O terminal. The determination result can also be output

externally. Remote must be turned ON in order to perform GO/NO-GO determination

using an external signal.

11.9 GO/NO-GO Determination Using Measured Waveform Parameters

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды