manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 201

15-10

IM 701210-06E

15.4 Performing Differentiation and Integration

(DSP Channels)

<For a description of this function, refer to page 2-50.>

Procedure

MEASURE CURSOR

RESET

SELECT

CH

ALL  CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

 1

CH

 2

CH

 3

CH

 4

CH

 5

CH

 6

CH

 7

CH

 8

CH

 9

CH

 10

CH

 11

CH

 12

CH

 13

CH

 14

CH

 15

CH

 16

DELAY

MANUAL  TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG  D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

7

DSP 1

8

9

DSP 2

6

5

4

1

0

2

3

ENTER

m

DSP 6

DSP 5

LOGIC  A

LOGIC  B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

1.

Press 

SHIFT+CH1 to CH6 

(DSP1 to DSP6).

Note

For a description of turning ON/OFF the DSP, see section 5.1.  For a description of setting
the vertical position, see section 5.4.  For a description of zooming vertically by setting the
zoom rate, see section 5.8.  For a description of setting waveform labels, see section 8.10.

Setting the Computation Definition

2.

Press the 

Setup 

soft key.  A setup dialog box opens.

3.

Use the 

jog shuttle 

and 

SELECT 

to set Operation to Diff(S1) (differentiation) or

Integ(S1) (integration).

Selecting the Channel on Which to Perform Computation

4.

Use the 

jog shuttle 

and 

SELECT 

to select Source1.

Setting Differentiation and Integration

• When Diff(S1) Is Selected

5.

Use the 

jog shuttle 

and 

SELECT 

to set Filter to ON or OFF.

6.

Use the 

jog shuttle 

and 

SELECT 

to set the CutOff in the range of 2.0% to

30.0%.  Proceed to step 7.

• When Integ(S1) Is Selected (Selecting the Reset Condition)

5.

Use the 

jog shuttle 

and 

SELECT 

to set the each item of Auto Reset Condition

to ON/OFF.  Proceed to step 7.

Note

If Over Limit is turned ON, the computation is reset when the computed result e10
divisions or –10 divisions of the Value/Div setting.  If Zero Cross to Positive is turned ON, the
computation is reset when the signal of the target channel produces a positive edge at the
zero-crossing point.  If Zero Cross to Negative is turned ON, the computation is reset when
the signal of the target channel produces a negative edge at the zero-crossing point.  Multiple
items can be selected simultaneously.

Diff (S1): differentiation

Integ (S1): integration

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды