YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 193

Страница: 193 / 406

15-2

IM 701210-06E

15.1 DSP Channels (Optional)

Notes Concerning DSP Channels

Notes When Using the DSP Channels as Computation Sources

• The maximum computation rate is 100 kS/s. If this rate is exceeded, the data is

automatically re-sampled at 100 kS/s.

• The computed result is displayed in 16 bits (fixed decimal point). (Computation is

performed using 32-bit floating-point decimal values, but the value is normalized to 16

bits after computation and saved to the acquisition memory.)

• All modules are computation sources.

• Analog channels (CH1 to CH16) are specified as computation sources. The

computed result of a DSP channel can also be specified as a computation source of

another DSP channel. However, only DSP channels with a channel number smaller

than itself can be specified.

Notes Concerning Display

• Value/Div Setting

The unit of the computed result of DSP channels is expressed as “Value/Div,”

because the result may not necessary be a voltage depending on the selected

computing equation.

Value/Div:

123 Value/Div different settings can be specified using the V/DIV knob

(1-2-5 steps).

10.00E–21 [Value/Div] to 500.0E+18 [Value/Div]

• Variable Setting

• When variable is set to OFF (zooming in or out by setting the zoom rate)

Zoom rate:

The following zoom rates are available.

0.1,

0.111,

0.125,

0.143,

0.167,

0.2,

0.25,

0.33,

0.4,

0.5,

0.556,

0.625,

0.667,

0.714,

0.8,

0.833,

1.11,

1.25,

1.33,

1.43,

1.67,

2.22,

2.5,

3.33,

6.67,

10,

12.5,

16.7,

20,

25,

40,

50, and

100

Zoom position: The waveform is zoomed around the vertical position.

• When variable is set to ON (vertical zoom/expand according to the upper and

lower limits of the display range)

Upper and lower limits:

5.0000E+22 [Value/Div]/

1.0000E–23 [Value/Div]

Display range:

Up to

5.0000E+21.(500.0E+18 [Value/Div]

10 [Div])

The display will be clipped at higher values.

• Computation Delay

[4 s the delay of the digital filter

]

Varies depending on the computation rate (100 kS/s maximum) of the DSP channel.

If the output result of a DSP channel is specified as a source of another DSP channel,

the computation delay increases.

1. For details on the computation delay of the digital filter, see appendix 6.

Notes on Other Items

• When the DSP channel is ON, the sample rate of the analog channel is limited to 5

MS/s maximum.

• You must set the sample rate to 2 MS/s or lower before turning the DSP channel

display ON or OFF.

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды