manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 237

16-26

IM 701210-06E

Preparations for Using the Web Server Function

Connecting the PC and the DL750/DL750P to the Network

Connect the PC and the DL750/DL750P to the network.  For the connection procedure,

see section 16.1.

Preparations on the DL750/DL750P

• Setting the Communication Interface to Network

FILE

SHIFT

HELP

MISC

NUM  KEY

PROTECT

VOICE
MEMO

IMAGE

SAVE

PRINT

SNAPSHOT CLEAR  TRACE

MENU

MENU

Turn ON the power to the DL750/DL750P.  After the DL750/DL750P boots up

normally, carry out the following procedure.

1.

Press 

MISC

.  The MISC menu appears.

2.

Press the 

Remote Cntl

 soft key.  The Remote Cntl menu appears.

3.

Press the 

Device

 soft key.  The Device menu appears.

4.

Press the 

Network

 soft key.  The Ethernet interface is selected for the

communication means.

• Setting up the TCP/IP

5.

Set the TCP/IP on the PC and the DL750/DL750P.  For the procedure on the

DL750/DL750P, see section 16.2.

• Setting the User Account Used to Access the DL750/DL750P

6.

Set the user account used to access the DL750/DL750P from the PC.  For the

procedure, see section 16.6.

Note

The User Account in the menu that appears after step 4 is the user account that is used to
control the DL750/DL750P through communication commands via the Ethernet network.  It is
not the user account for using the Web server function.

• Setting the Time Difference from GMT (Greenwich Mean Time)

7.

Set the time difference between the location where the DL750/DL750P is

located and the GMT.  For the procedure, see section 16.8.

• Rebooting

8.

To activate the TCP/IP, user account, and time difference settings, turn OFF the

power switch.  After a few seconds, turn ON the power switch and boot the

DL750/DL750P.

16.7 Using the Web Server Function

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды