YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 277

Страница: 277 / 406

18-6

IM 701210-06E

18.2 Messages and Corrective Actions

Code

Message and Corrective Action

Section

836

Cannot change settings during Action On Trigger. Stop the Action On Trigger.

6.18

837

Cannot set the channels which do not have modules installed.

–

838

Cannot set the channels which do not have the strain module installed.

–

839

Cannot Set or Execute.

11.10

840

If the trigger mode is set to Single, Single (N), or LOG, the acquisition mode cannot be set to Average.

6.1, 7.3

843

If the acquisition mode is Average, the trigger mode cannot be set to Single, Single (N), or Log.

6.1, 7.3

844

It can’t be set at the time of the roll mode.

5.2

845

The trigger mode cannot be set to Single(N) during the roll mode.

5.2, 6.1

850

The acquisition mode cannot be set in the current record length.

7.2

851

Computation cannot be carried out at the current record length.

7.2

853

Cannot be configured or executed during the search operation.

11.2 to 11.4

855

Cannot be configured or executed during the history search operation.

11.2, 11.3

856

The record cannot be selected.

11.1 to 11.3

857

History record does not exist.

11.1 to 11.3

858

Cannot be configured or executed while computation is in progress.

11.1 to 11.3

Aborted when history display mode is set to One.

859

It can’t be set up or be carried out in the Preview mode.

12.2

Choose Quit, and cancel the Preview mode.

860

Cannot be configured or executed while updating the history all display.

11.1 to 11.3

Aborted when history display mode is set to One.

861

This format cannot output with color.

12.3, 12.4

862

Zones cannot be edited in the following cases: When the main window is not displayed.

11.9

When the relevant waveform is not displayed.

863

The zone waveform does not exist.

11.9

865

Zones determination is not possible in the following cases:

11.9

When the main window is not displayed. When the relevant waveform is not displayed.
When the zone waveform does not exist.

867

Conflict in the waveform display plane.

11.9

Set the Mode to something other than Zone using the GO/NO-GO menu.

868

Processing statistics.

11.7

To perform other operations, abort the statistical processing.

869

The channel which couldn’t be set up was specified.

Chapter 11,
13.7

870

Cannot be set when the acquisition mode is set to average.

7.3

871

Cannot be set in the dual capture mode.

7.6

872

Cannot be set during realtime recording.

7.7

873

It is an unacceptable parameter to set up to the present module.

Chapter 5

874

It can't be set up during the dual capture practice.

7.6

875

Cannot be set to a range of 20 sec/div to 3 day/div during roll display.

5.2

876

Because a record length is too long, it can’t be set up by the present number of indication channels.

7.2

877

Cannot be set because there are too many display channels at the current record length.

7.2

Shorten the record length.

878

Zooming is not available when the number of displayed points of the FFT waveform is less than 50

10.3

in the Zoom window. Aborted when history display mode is set to One.

879

It is the dual capture record length which can’t be set up.

7.6

880

Cannot change this setting during realtime recording.

7.7

881

The time base cannot be set to external clock when the acquisition mode is set to envelope or

7.3, 5.14

box average.

882

Spaces are not allowed for trace labels.

8.10

883

Cannot set accumulate during roll mode display.

5.2, 8.4

884

Cannot change the History parameter when accumulate is ON. Turn OFF accumulate first.

8.4

885

P-P compression cannot be used to save when a record length is 1 K.

13.7

886

Event channels cannot be displayed at the current record length.

7.2, 5.21

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды