manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 309

19-21

IM 701210-06E

Specifications

19

19.12 Module Specifications

Item

Specifications

Compatible probes/cables Voltage probe (10:1 safety probe): Recommended

700929 (10:1 safety probe).20 to 45 pF: For measuring 600 Vpeak or less

Current probe (power can be supplied from the DL750/DL750P)

700937 (15 A), 701930 (150 A), 701931 (500 A), 701933 (30 A)

High voltage differential probe (connect the GND cable provided with the probe to the DL750/
DL750P case)

700924 (1000:1, 100:1/1400 Vpeak): For measuring 1400 Vpeak or less

Connection cable (for high voltage 1:1)

701901 (isolated type BNC-safety alligator clip adapter 

×

2: For measuring 250 V peak or less), a

separate alligator clip (701954) is required

Connection cable (for low voltage 1:1)

366926 (non-isolated type BNC-alligator clip 

×

2: For measuring low voltage less than or equal to

42 Vpeak)

1.

Value measured under standard operating conditions (section 19.11).

H

L

Combined with the 700929

2.

3.

700929

H

L

701901

701954

4.

Combined with the 701954

H

L

Direct input (cable not complying with the safety standard)

6.

7.

BNC

5.

Withstand voltage: 1500 Vrms for 1 minute
Allowable transient surge voltage: 

±

2100 Vpeak

(between earth and input)

8.

The typical value is a representative or standard value.  It is not strictly warranted.

WARNING

• Do not apply input voltage exceeding the maximum input voltage, withstand

voltage, or allowable surge voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

• To prevent the possibility of electric shock, be sure to fasten the module screws.

Otherwise, the electrical and mechanical protection functions will not be

activated.

• Avoid continuous connection under an environment in which the allowable surge

voltage or higher voltage may occur.

• To prevent the possibility of electric shock, be sure to connect the GND lead of

the differential probe (700924/700925) to the DL750/DL750P.

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды