manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 208

15-17

IM 701210-06E

Using the DSP Channel (Optional)

15

Setting the Elimination Level

8.

Use the 

jog shuttle 

and 

SELECT 

to set Elimination Level.  Press ESC.

Setting Value/Div

9.

Turn the V/DIV knob to set the Value/Div value.

You can also set Value/Div by pressing the 

Value/Div 

soft key and turning the

jog shuttle

.

Note

There are 123 (selectable range: 10.00E–21 [Value/Div] to 500.0E+18 [Value/Div]) different
Value/Div settings.  You set the Value/Div using 1-2-5 steps similar to the V/div setting.

Automatically Selecting the Optimum Value/Div Setting

10.

Press the 

Optimize Value/Div 

soft key.  The optimum Value/Div setting is

automatically selected by referring to the range of the computation channel and

displayed.

Note

•

The Optimize Value/Div soft key appears only when Variable is OFF.

•

When using the knocking filter, the range is set to the same range as the computed
channel.

Zooming in on the Waveform

The procedure of “Zooming in or out Vertically by Setting the Zoom Rate” and “Zooming/

Expanding Vertically According to the Upper and Lower Limits of the Display Range” is

the same as the procedure described in section 15.2, “Performing Addition, Subtraction,

Multiplication, and Division (DSP Channels).”  See page 15-4.

Setting the Waveform Label

The procedure is the same as the procedure described in section 15.2, “Performing

Addition, Subtraction, Multiplication, and Division (DSP Channels).”  See page 15-4.

Setting the Unit

The procedure is the same as the procedure described in section 15.2, “Performing

Addition, Subtraction, Multiplication, and Division (DSP Channels).”  See page 15-4.

Variable OFF

Variable ON

15.6 Using the Knocking Filter (DSP Channels)

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды