YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 131

Страница: 131 / 406

13-18

IM 701210-06E

Selecting the Range of Waveform to Be Saved

Press the

Range

soft key. A menu for selecting the range of waveform to be

saved appears.

10.

Press the

Main

, or

soft key to select the waveform save range.

11.

Press the

History

soft key to save all the data in the history memory (All), save

only the selected waveform (One), or save the average data in the history

memory (Ave).

If you select All after performing a search on the history memory data, only the

searched waveforms are saved.

Compressing the Data and Saving/Decimating the Data and Saving

• Decimating the Data and Saving (When Data Type Is Set to ASCII)

12.

Press the

Save Interval

soft key.

Turn the

jog shuttle

to set the save interval from OFF, Per5 to Per5000.

• Compressing the Data and Saving (When Data Type Is Set to Binary)

12.

Press the

P-P Comp

soft key to select ON (compress and save) or OFF (do not

compress and save).

If P-P Comp is turned ON when saving waveform data, only the maximum and

minimum values of the multiple data points existing at the same time position

are saved. Consequently, the file size is reduced.

Note

If P-P Comp is set to ON, you cannot set the save range using Range.

For Data
Type: Binary

For Data
Type: ASCII

13.7 Saving/Loading the Waveform Data

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды