YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 127

Страница: 127 / 406

13-14

IM 701210-06E

Media Info

Lists the information about the selected medium. The following information is displayed.

• Media Name: Name of the medium.

• Media Size:

Total size.

• Used Space: Size of the used area.

• Vacant Space: Size of the free area.

• Partition Size: Number of partitions.

Note

•

If you format a medium that has data stored on it, all the data are cleared when the
medium is formatted.

•

It takes approximately a minute and a half to format a floppy disk.

•

It takes approximately 10 s to format a 250-MB Zip disk.

•

It takes a few seconds to format a PC card.

•

It takes approximately 30 s to 1 minute to format the internal hard disk (optional).

•

You cannot format a floppy disk if the write-protect is ON.

•

Do not format a disk while the DL750/DL750P and a PC is connected via a SCSI cable.

•

Floppy disks that are formatted to formats other than those listed in this section cannot be
used.

•

If an error message is displayed after the format operation, the target medium may be
damaged.

•

You can use floppy disks that are formatted using MS-DOS on a PC.

•

This function cannot be used when using the FTP server function, the FTP client function,
network printer function or the Web server function.

13.5 Formatting the Storage Medium

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды