YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 210

Страница: 210 / 406

15-19

IM 701210-06E

Using the DSP Channel (Optional)

The cutoff frequency, center frequency, and pass band can be specified in terms of

percentages of fs (sampling frequency).

Type

Filter Band

Cutoff Frequency

Center Frequency

Pass Band

Sharp

HPF

2.0% to 30.0%

BPF

3.0% to 30.0%

2% of fs

4.6% to 30.0%

5% of fs

7.0% to 30.0%

10% of fs

9.6% to 30.0%

15% of fs

12.0% to 30.0%

20% of fs

IIR

HPF

0.2% to 30.0%

BPF

0.6% to 30.0%

1% of fs

1.2% to 30.0%

2% of fs

2.6% to 30.0%

5% of fs

5.2% to 30.0%

10% of fs

7.6% to 30.0%

15% of fs

10.2% to 30.0%

20% of fs

Diff (differentiation) Performs the same computation as the differentiation described in section

15.4.

HPF: High-pass filter, BPF: Band-pass filter

The cutoff frequency (CutOff) can be specified only when HPF is selected.
The resolution is 0.2%.

The center frequency can be specified only when BPF is selected.
The resolution is 0.2%.

The pass band can be specified only when BPF is selected.
You can select the pass band from 1%, 2%, 5%, 10%, 15%, and 20%.

Setting the Elimination Level

Set the reference level for noise elimination. The selectable range and resolution of the

elimination level are the same as those of the trigger level. See section 6.5.

Setting Value/Div

Like V/div, Value/Div is set using 1-2-5 steps. The selectable range is 10.00E–21

[Value/Div] to 500.0E+18 [Value/Div] with 123 settings.

Turn the V/DIV knob to set the Value/Div value. You can also set Value/Div by pressing

the Value/Div soft key and turning the jog shuttle.

Automatically Selecting the Optimum Value/Div Setting

When you press the Optimize Value/Div soft key, the optimum range is automatically

selected from the 123 Value/Div settings, and the waveform is displayed using the

selected setting.

Zooming in on the Waveform

• Zooming in or out Vertically by Setting the Magnification

For details, see section 5.8, “Zooming Vertically by Setting the Zoom Rate” and

“Notes Concerning Display” in section 15.1.

• Zooming/Expanding Vertically According to the Upper and Lower Limits of the

Display Range

For details, see section 5.9, “Zooming Vertically According to the Upper and Lower

Limits of the Display Range” and “Notes Concerning Display” in section 15.1.

15.6 Using the Knocking Filter (DSP Channels)

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды