manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 272

18-1

IM 701210-06E

Troubleshooting, Maintenance, and Inspection

18

Chapter 18

Troubleshooting, Maintenance, and Inspection

18.1 Troubleshooting

Troubleshooting

• If a message is displayed on the screen, read the succeeding pages.

• If servicing is necessary, or if the instrument is not operating correctly after performing

the corrective actions below, contact your nearest YOKOGAWA dealer.

Problem

Probable Cause

Corrective Action

Reference
Section

The power cannot be

Using a power supply outside the

Use a correct power supply.

3.4

 turned ON.

ratings.

Nothing is displayed.

The backlight is turned OFF.

Press any key.

17.5

The screen colors are not

Power cycle the DL750/DL750P while

17.4

appropriate.

holding down the 

RESET 

key.

The display is odd.

The system is abnormal.

Power-cycle the DL750/DL750P.

3.4

Keys do not work.

The DL750/DL750P is in

Press 

SHIFT + CLEAR TRACE 

enable

–

the remote mode.

local mode.

Other causes.

Perform a key test.

18.3

If the test fails, servicing is required.

Protected.

Press the 

PROTECT 

key.

17.6

Trigger does not activate.

The trigger settings are not

Set the trigger conditions correctly.

Chapter 6

appropriate.

Measured values are not

Insufficient warm-up.

Warm up the DL750 for 30 minutes

—

correct.

after turning on the power.

Not calibrated.

Perform a calibration.

4.6

The probe’s phase has not been

Correct the phase properly.

3.7

corrected.

The probe attenuation is not correct. Set an appropriate value.

5.6

An offset voltage is added.

Set the offset voltage to 0 V.

5.10

Other causes.

Perform a calibration.  In addition,

4.6

select Test Item: Carib.Inf. for the self

18.3

test item and execute the self test.
If the measured value is still odd,
servicing is required.

Cannot output to built-in

The printer head is damaged or

Servicing required.

–

printer.

worn out.

Cannot save to the specified

The medium is not formatted.

Format the medium.

13.5

medium.

The medium is write-protected.

Release the medium’s write-protect.

–

No more free space on the medium. Delete unneeded files or use a new

13.15

medium.

Cannot change settings or

The address of the DL750/DL750P

Match the address used in the program

Communication

control the operation of the

used by the program is different

to the address of the DL750/DL750P.

Interface

DL750/DL750P via the

from the specified address.

User’s Manual

communication interface.

The interface is not used in a way

Use it in a way that conforms to the

(IM701210-18E)

that conforms to the electrical or

specifications.

mechanical specifications.

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды