YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 115

Страница: 115 / 406

13-2

IM 701210-06E

Zip Disks

Zip Disks That Can Be Used

The following types can be used. You can format the disk on the DL750.

Size:

100 MB or 250 MB

Format:

FDISK 1 partition (hard disk format)

Inserting the Zip Disk into the Zip Drive

With the label facing toward you, insert the disk from the side with the shutter.

Removing the Zip Disk from the Zip Drive

With the DL750 turned ON, check that the access indicator is OFF and press the eject

button.

If you need to use the Zip disk again, wait at least three seconds after removing it before

reinserting it into the drive.

Eject button
Access indicator

Label side

13.1 Floppy Disks/Zip Disks/PC Cards

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды