YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 136

Страница: 136 / 406

13-23

IM 701210-06E

Saving and Loading Data

Data Size

The following table shows the data size when the record length is set to 100 kW,

waveform data of CH1 to CH4 are saved, all Math channels are turned OFF, and using

history waveform 1 condition.

Data Type

Extension

Data Size (Bytes)

Binary

.WVF

Approx. 800 K ((100 kW + 32)

4 channels

the number of

history waveforms

.HDR

Approx. 2 K (approx. 3 K when Math1 and Math2 are ON)

ASCII

.CSV

4 to 5 MW

Float

.FLD

Approx. 1.6 M ((100 kW + 32)

the number of history

waveforms

Waveform to Be Saved: Trace

• You can save all the waveforms or the specified waveforms from CH1 to CH16, DSP1

to DSP6 (optional), Math waveforms, logic waveforms, and event waveforms.

• The setup parameters including vertical axis, horizontal axis, and trigger of the

waveform to be saved are also saved.

• For waveforms that are loaded using the history memory function, you can select

whether to save all of the history data, save the average of the history data, or save

just the current displayed waveform on the screen. If History is set to All, MATH

channels are not saved. If you wish to save the data of MATH channels, set History

to One. You can also save only the results obtained by searching the history memory

data. For a description of searching the history memory data, see section 11.2.

• For a description of snapshot waveforms, see section 13.9.

Selecting the Range of the Waveform to Be Saved

Select the range (region) of the waveform from the following list of choices. Only the

data that has been saved by selecting Binary in the aforementioned section “Selecting

the Data Type” can be loaded in the DL750/DL750P.

• Main

The range of the normal (Main) waveform. It is the range defined by the displayed

record length (range displayed on the screen).

• Z1

The range of zoom waveform Z1.

• Z2

The range of zoom waveform Z2.

Compressing the Data and Saving: P-P Comp (When Data Type Is Set to Binary)

You can select whether to P-P compress the waveform data before saving.

Power spectrum computation data cannot use P-P compression.

Decimating the Data and Saving: Save Interval (When Date Type Is Set to ASCII)

When saving to ASCII format, data is decimated and converted to ASCII format before

the data is saved.

Save Interval:

OFF (no decimation), Per 5, Per 10, Per 20, Per 50, Per 100, Per 200,

Per 500, Per 1000, Per 2000, and Per 5000

For example, if Per 5 is selected, the data is decimated as follows.

“First data point” “+5” “+10” “+15” ...

13.7 Saving/Loading the Waveform Data

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды