YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 281 | Manualshive

Страница: 281 / 406

YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 281

18-10

IM 701210-06E

18.2 Messages and Corrective Actions

Code

Message and Corrective Action

Section

1125

Cannot directly load the sub waveform file (for example 0003DC.WVF).

7.6, 13.7

Specify and load the main waveform file (for example 0003.WVF).

1126

Cannot save in this format at the current record length. Specify a range and save a section of the data. 7.2
* Cannot create a file of size 2 GB or larger.

1127

Cannot load because the medium is selected. Select a setup file (SET).

13.8

1128

Cannot load because a directory is selected. Select a setup file (SET).

13.8

1129

Cannot load because the medium is selected. Select a binary file (.WVF).

13.7

1130

Cannot load because a directory is selected. Select a binary file (.WVF).

13.7

1131

Cannot load files larger than 50 MB on a network drive. Copy the file to the local drive before loading it. Chapter 13

1132

Cannot load a HistoryAll binary file on a network drive.

13.7

1133

Turn the HDD motor ON.

Chapter 13

1134

If the realtime recorded file is converted to binary format, the converted file cannot be loaded.

13.7, 13.14

1135

Cannot save the waveform by specifying Z1 (Z2) for the range to be saved, if the zoom rate is set to x1. 13.7
Save the waveform by specifying Main for the range to be saved.

1136

The file saved on the DL750P when the recorder mode is set to chart or X-Y cannot be loaded in the

Chapter 9

DL750.

1137

Cannot make a directory or a file in the real-time area of the internal hard disk.

7.7,

Change the current directory.

Chapter 13

1138

Cannot save at the current PDF setting.

9.9, 13.13

Change the settings.
* A file of size exceeding 2 GB cannot be created.

1139

Cannot create PDF files on the network drive when the history waveform display format is set to All.

9.9, 13.13

Create the file on the local drive, and then copy it to the network drive.

Printer Errors (1200 to 1299)

Code

Message and Corrective Action

Section

1200

Move the release arm to the “HOLD” position.

12.1

1201

Paper empty. Load a roll chart.

12.1

1202

The printer head temperature is high. Printing will be aborted.

12.1

Printing will not be possible until the printer head temperature comes down.

1203

Printer over heat. Power off immediately.

12.1

1204

Printer power supply error. Maintenance service is required.

12.1

1205

Printer time out. Maintenance service is required.

12.1

1206

USB printer error. Turn the power of the printer from OFF to ON.

12.3

1207

USB printer off-line.

12.3

1208

No paper.

12.3

1209

USB printer is in use.

12.3

1210

Cannot detect printer. Turn ON the printer. Check connectors.

12.3

1211

Printer is out of order. Maintenance service is required.

12.4

1212

Printer error. Turn the power of the printer from OFF to ON.

12.4

1213

Printer offline.

12.4

1214

Out of paper.

12.4

1215

Printer is in use.

12.4

1216

Cannot detect printer. Turn ON the printer. Check connectors.

12.4

1217

No applicable files for showing thumbnails.

13.12

1218

Print head temperature detection thermister is broken.

–

1219

Print head temperature detection thermister is shorted.

–

1220

Thumbnail execution is not possible when the floppy drive is specified.

13.12

Select the image file from the file list and confirm with the SELECT key.

«
...
279
280
281
282
283
...
»

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды