YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 275

Страница: 275 / 406

18-4

IM 701210-06E

18.2 Messages and Corrective Actions

Code

Message and Corrective Action

Section

742

Because there are too many channels, it can’t start in the length of the present record.

7.2

743

The indication mode of the history can’t be carried out except for “Average”.

11.1

744

Average practice can’t be done because the record length of the history exceeds the record length

11.1

that it can be carried out.

745

Set the trigger mode to Auto or Log for realtime hard disk recording.

6.1, 7.7

If the number of actions is set to Continuous, the only valid trigger mode is Log.

746

Dual capture is not possible at the current record length. Shorten the memory length.

7.6

747

Dual capture is not possible if the main sample rate is faster than 100 kS/s or T/div is faster than

5.2, 7.2, 7.6

100 msec/div. Meet either of the conditions below.

• Shorten the record length (slower sample rate).
• Decrease T/Div.

748

Cannot start at the current record length.

5.2, 6.1,

Shorten the record length or meet the following condition.

7.2

• Set the trigger mode to Auto, decrease T/Div to less than 100 msec/div to enable roll mode.
• Set the trigger mode to Single or Log.

749

Averaging mode is not possible when the trigger mode is Single, SingleN, or Log.

6.1

Change the trigger mode.

751

A trigger can’t start in case of dual capture in case of the one except for Auto or Log.

6.1, 7.6

Please change the trigger mode.

752

Dual capture is not possible when set to average. Change the acquisition mode.

7.3, 7.6

753

Cannot start when the HISTORY or SEARCH menu is being displayed.

11.2

Press the ESC key to clear the menu before starting.

754

Dual capture is not possible when set to X-Y or T-Y&X-Y.

7.6, 8.6

The capture window connot be opened when set to X-Y or T-Y&X-Y.

755

Time base cannot be set to external clock when set to envelope or box average.

5.14, 7.3

756

Cannot set accumulate during roll mode display. Turn Off accumulate.

5.2, 8.4

757

Cannot be executed when the acquisition mode is set to average. Change the mode.

7.3

758

Cannot copy if 50 pages is exceeded. Change the multiplier or range.

12.2

759

Realtime recording to the internal hard disk is valid when the record length is longer than 1 M.

7.2, 7.7

760

Cannot set the current drive on a realtime partition using communication commands.

7.7

761

Cannot be executed on realtime recorded waveforms.

7.7

762

Cannot be executed on waveforms in dual capture mode.

7.6

763

Long copy is not possible when X-Y display is present.

8.6

764

File recorded in realtime is currently being analyzed. Files being analyzed cannot be deleted.

7.7, 13.4

765

File recorded in realtime is currently being analyzed.

7.7, 13.17

The name of files being analyzed cannot be changed.

766

File recorded in realtime is currently being analyzed.

7.7, 13.5

Partitions containing files that are being analyzed cannot be formatted.

767

128 and more file can’t be formed in the real-time area.

7.7

768

The file which failed in the real-time record can’t be read.

7.7

769

Cannot start Single(N) when accumulate is On. Change the accumulate to Off.

6.1, 8.4

770

Cannot be executed when GO/NO-GO Mode is Zone.

11.9

771

Cannot play voice memo in the following situations:

7.9

* while waveforms are being read
* when history display mode is not One
* when the latest history record is not displayed

772

Cannot record a voice memo when not in roll mode.

7.9

773

The measuring range is up to 10 MWords from measure start (TimeRange1).

6.17

774

Synchronizing signal not detected.

6.17

775

Set acquisition mode to Normal when using a wave window trigger.

6.17

776

The wave window trigger cannot be used if the sampling rate is faster than 500 kS/s or slower than 10 kS/s. 6.17

777

Range over. Change to an appropriate range then retry shunt calibration.

5.17

778

Statistical processing cannot be performed on waveforms recorded in real time.

11.7

779

Cannot detect a effective input signal at a Sync. channel.

6.17

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды