YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 71

Страница: 71 / 406

11-33

IM 701210-06E

Waveform Analysis/Search

Setting the 1 Cycle Mode

18.

Press the

1Cycle Mode

soft key to select ON or OFF.

Setting the Measurement Range

19.

Press the

Time Range1/Time Range2

soft key to set the jog shuttle control to

Time Range1.

20.

Turn the

jog shuttle

to set the measurement start point.

21.

Likewise, set Time Range2 (measurement end point).

Note

Up to 10 MW from the measurement start point (Time Range1) are measured.

Selecting the Target Waveform for Distal, Mesial, and Proximal Points

22.

Press the

Next 1/2

soft key

23.

Press the

Trace

soft key. The trace selection menu appears.

24.

Press the soft key corresponding to the desired waveform to select the target

waveform.

Setting the Distal, Mesial, and Proximal Unit

25.

Press the

Dist/Prox Mode

soft key to set the unit for distal, mesial, and proximal

points to % or Unit. If the target waveform was set to DSP1 to DSP6 (optional)

in steps 23 and 24, only % is selectable.

Setting Distal, Mesial, and Proximal

26.

Press the

Distal

Mesial

, or

Proximal

soft key.

27.

Turn the

jog shuttle

to set the distal, mesial, or proximal point.

Selecting the High and Low Setting

28.

Press the

High/Low Mode

soft key to select Auto or MAX-MIN.

DSP1 to DSP6 are optional.

11.6 Automated Measurement of Waveform Parameters

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды