YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 45

Страница: 45 / 406

11-7

IM 701210-06E

Waveform Analysis/Search

Explanation

You can search for a waveform that matches the specified conditions from the past

waveforms in the acquisition memory and display it.

Select Zone

Four types of search zones can be registered in Zone1 to Zone4. You can set the

channel that is to be searched, the search condition, and the search range for each

search zone.

Condition

IN:

Searches for waveforms that pass through the specified search window.

OUT:

Searches for waveforms that do not pass through the specified window.

OFF:

Does not search for waveforms.

Source

Search is carried out on the channel that is specified as the Source. The channels that

can be specified are CH1 to CH16 and DSP1 to DSP6 (optional). Waveforms of other

channels are also displayed.

Vertical Range of Search Window: Upper/Lower

The selectable range is

5 divisions. The resolution is 0.01 divisions.

Upper must always be greater than or equal to Lower.

Horizontal Range of Search Window: Left/Right

The selectable range is

5 divisions. The resolution is (10 division/display record

length).

Right must always be greater than or equal to Left.

Logic

AND: Searches for waveforms that meet all search conditions from Zone1 to Zone4.

OR:

Searches for waveforms that meet any one of the search conditions from Zone1

to Zone4.

Search Range of History Memory Data

The search range is between the Start Rec and the End Rec.

Search Order

The search is carried out from the newest waveform to the oldest waveform.

Show Map (A List of Time Stamps)

Only the waveforms that are found are listed in Show Map. If the Search Mode is turned

OFF, all waveforms are displayed.

11.2 Searching History Memory Data Using Zones (History Search Function)

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды