manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 185

13-72

IM 701210-06E

Explanation

A voice comment can be recorded when saving screen image data by connecting an

earphone microphone with a PUSH switch to the DL750/DL750P.

Record Time

A voice comment of up to 10 s in length can be attached to a singe screen image data

file.

Recording a Voice Comment: Rec Start/Rec Stop

The voice comment that is saved at the time the screen image data is saved is the voice

comment that was recorded immediately before the data is saved.  A voice comment is

saved to a single screen image data file (never to multiple files).

Note

The voice comment is saved as data separate from the screen image data.  For a description
of the extension of voice comment data file, see the explanation in section 13.11.  To erase
only the voice comment of the saved screen image data, erase the relevant voice comment
data on the File List window of the FILE menu.  (For the procedure of displaying the File List
window, see steps 1 to 7 on page 13-44.  For the procedure of erasing the data, see section
13.15.)

Playing a Voice Comment (Confirmation before Saving the Data): Play

You can play the recorded voice comment to check the contents before saving the data.

If you wish to change the voice comment after playing it, record the voice comment

again.

The voice comment can be overwritten any number of times until the screen image data

is saved.  Thus, the voice comment that is saved along with the screen image data is the

voice comment that is recorded immediately before the data is saved.

Erasing Voice Comments

The recorded voice comment is erased.  Use caution because voice comments that are

erased cannot be recovered.

13.19  Using the Voice Comment Function

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды